View in EDS

Influence of fin size and distribution on solid-liquid phase change in a rectangular enclosure.

Saved in:
Bibliographic Details
Title: Influence of fin size and distribution on solid-liquid phase change in a rectangular enclosure.
Authors: Biwole, Pascal Henry1,2 pascal.biwole@uca.fr, Groulx, Dominic3, Souayfane, Farah4,5, Chiu, Tim4
Source: International Journal of Thermal Sciences. Feb2018, Vol. 124, p433-446. 14p.
Subjects: Phase change materials, Natural heat convection, Thermal management (Electronic packaging), Solid-liquid interfaces, Heat transfer fluids, Navier-Stokes equations, Buoyancy
Abstract: This paper details a numerical study of solid-liquid phase change heat transfer in a rectangular enclosure with the aim of optimizing the number, dimension, and positioning of fins in the enclosure. The enclosure is exposed on one side to a constant heat flux of 1000 W/m 2 for 3 h and both the total fin mass and the PCM mass are kept constant in all simulated cases. The heat diffusion equation in the PCM uses the equivalent heat capacity method while natural convection driven PCM motion in the enclosure is modeled through the buoyancy force, using a modified viscosity and an additional volume force term in the Navier-Stokes momentum conservation equation. Three efficiency assessment parameters are used: (i) the height-averaged temperature of the front hot plate which should remain as low as possible for the longer possible time, (ii) the energy stored inside the PCM as a function of time, and (iii) the heat transfer rate and heat flux between the front plate and the PCM. For each simulated case, complementary data such as the standard deviation of temperature along the heated plate and the ratio of sensible heat to latent accumulation are also calculated. Results show that increasing the number of fins diminishes both the stabilization temperature and the stabilization time of the front plate during phase change, and accelerates the sensible and latent storage of energy in the PCM. Using thinner but longer fins provides the same impact except that the stabilization time also increases as the fin length is increased. Besides, at constant fin mass, varying fin spacing have marginal impact on the latent heat storage performance and on the hot plate temperature stabilization. The study also shows that the surface area plays the largest role in the increase of the heat transfer rate between the front plate and the PCM, while configurations which can promote stronger natural convection lead to higher heat flux. Finally, it was observed that systems allowing easier heat transfer to the back plate during melting provide a higher ratio of sensible heat to latent accumulation, while the standard deviation of the front plate temperature decreases as the number of fins or the spacing between fins increases. [ABSTRACT FROM AUTHOR]
Copyright of International Journal of Thermal Sciences is the property of Elsevier B.V. and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)
Database: Engineering Source
Description
Abstract:This paper details a numerical study of solid-liquid phase change heat transfer in a rectangular enclosure with the aim of optimizing the number, dimension, and positioning of fins in the enclosure. The enclosure is exposed on one side to a constant heat flux of 1000 W/m 2 for 3 h and both the total fin mass and the PCM mass are kept constant in all simulated cases. The heat diffusion equation in the PCM uses the equivalent heat capacity method while natural convection driven PCM motion in the enclosure is modeled through the buoyancy force, using a modified viscosity and an additional volume force term in the Navier-Stokes momentum conservation equation. Three efficiency assessment parameters are used: (i) the height-averaged temperature of the front hot plate which should remain as low as possible for the longer possible time, (ii) the energy stored inside the PCM as a function of time, and (iii) the heat transfer rate and heat flux between the front plate and the PCM. For each simulated case, complementary data such as the standard deviation of temperature along the heated plate and the ratio of sensible heat to latent accumulation are also calculated. Results show that increasing the number of fins diminishes both the stabilization temperature and the stabilization time of the front plate during phase change, and accelerates the sensible and latent storage of energy in the PCM. Using thinner but longer fins provides the same impact except that the stabilization time also increases as the fin length is increased. Besides, at constant fin mass, varying fin spacing have marginal impact on the latent heat storage performance and on the hot plate temperature stabilization. The study also shows that the surface area plays the largest role in the increase of the heat transfer rate between the front plate and the PCM, while configurations which can promote stronger natural convection lead to higher heat flux. Finally, it was observed that systems allowing easier heat transfer to the back plate during melting provide a higher ratio of sensible heat to latent accumulation, while the standard deviation of the front plate temperature decreases as the number of fins or the spacing between fins increases. [ABSTRACT FROM AUTHOR]
ISSN:12900729
DOI:10.1016/j.ijthermalsci.2017.10.038