Lateral Torsional Buckling Design for Multi-Ply Structural Composite Lumber Beams.
Saved in:
| Title: | Lateral Torsional Buckling Design for Multi-Ply Structural Composite Lumber Beams. |
|---|---|
| Authors: | Waltz, Ned1 (AUTHOR) Ned.Waltz@weyerhaeuser.com, Amini, M. Omar2 (AUTHOR) OAmini@awc.org, Douglas, Bradford3 (AUTHOR) BDouglas@awc.org |
| Source: | Journal of Structural Engineering. Apr2024, Vol. 151 Issue 4, p1-15. 15p. |
| Subjects: | Engineered wood, Mechanical buckling, Bending strength, Flexural strength, Design techniques, Torsional stiffness, Composite construction, Research methodology |
| Abstract: | The objectives of this study were to investigate the lateral torsional buckling performance of multi-ply structural composite beams to develop experimental procedures to understand their flexural and torsional rigidity that can be used to develop design guidance capable of reliably accounting for their composite capacity. Three 44.5 mm×457 mm×14.8 mm (1.75 in.×18 in.×48.3 ft) laminated veneer lumber beams were nondestructively tested more than 140 times in this investigation using a variety of single and multi-ply member configurations to determine their member stiffness about each primary orientation and joist orientation buckling controlled moment capacity. To allow a wide range of member slenderness to be evaluated, the moment capacity tests used Southwell techniques and single-span bending configurations with two-point loads to determine the critical buckling moment capacity (Mtest′) and torsional rigidity for two different member depths, two different spans, two different relative load point positions, and with up to three beam plies. Multi-ply headers were attached together with nails using a scheme that approximated the manufacturer's minimum recommendations for applications without significant side loads. This study demonstrated that the measured lateral torsional buckling moment capacities were overpredicted where the multi-ply members were assumed to behave with the rigidity of a solid section and underpredicted where the members were assumed to behave as a collection of unattached plies. For the multi-ply beam loading conditions, nail attachment intensities, and bracing methods tested to near their full-scale buckling capacity in this study, Mtest′ was reasonably estimated using predictive calculations that explicitly accounted for torsional rigidity and assumed that the between-ply fastenings provided partial composite action with empirically derived efficiencies of 6% for torsional (GKJ) and 25% for plank orientation flexural (EpIp) rigidity. It was also found that the degree of multi-ply flexural EpIp composite action measured in the plank orientation flexural stiffness tests conducted under different loading and boundary conditions proved to be a poor predictor of relative lateral torsional buckling rigidity in the beam tests and was not correlated to the measured buckling resistance. [ABSTRACT FROM AUTHOR] |
| Copyright of Journal of Structural Engineering is the property of American Society of Civil Engineers and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.) | |
| Database: | Engineering Source |
| FullText | Text: Availability: 0 |
|---|---|
| Header | DbId: egs DbLabel: Engineering Source An: 183053948 AccessLevel: 6 PubType: Academic Journal PubTypeId: academicJournal PreciseRelevancyScore: 0 |
| IllustrationInfo | |
| Items | – Name: Title Label: Title Group: Ti Data: Lateral Torsional Buckling Design for Multi-Ply Structural Composite Lumber Beams. – Name: Author Label: Authors Group: Au Data: <searchLink fieldCode="AR" term="%22Waltz%2C+Ned%22">Waltz, Ned</searchLink><relatesTo>1</relatesTo> (AUTHOR)<i> Ned.Waltz@weyerhaeuser.com</i><br /><searchLink fieldCode="AR" term="%22Amini%2C+M%2E+Omar%22">Amini, M. Omar</searchLink><relatesTo>2</relatesTo> (AUTHOR)<i> OAmini@awc.org</i><br /><searchLink fieldCode="AR" term="%22Douglas%2C+Bradford%22">Douglas, Bradford</searchLink><relatesTo>3</relatesTo> (AUTHOR)<i> BDouglas@awc.org</i> – Name: TitleSource Label: Source Group: Src Data: <searchLink fieldCode="JN" term="%22Journal+of+Structural+Engineering%22">Journal of Structural Engineering</searchLink>. Apr2024, Vol. 151 Issue 4, p1-15. 15p. – Name: Subject Label: Subjects Group: Su Data: <searchLink fieldCode="DE" term="%22Engineered+wood%22">Engineered wood</searchLink><br /><searchLink fieldCode="DE" term="%22Mechanical+buckling%22">Mechanical buckling</searchLink><br /><searchLink fieldCode="DE" term="%22Bending+strength%22">Bending strength</searchLink><br /><searchLink fieldCode="DE" term="%22Flexural+strength%22">Flexural strength</searchLink><br /><searchLink fieldCode="DE" term="%22Design+techniques%22">Design techniques</searchLink><br /><searchLink fieldCode="DE" term="%22Torsional+stiffness%22">Torsional stiffness</searchLink><br /><searchLink fieldCode="DE" term="%22Composite+construction%22">Composite construction</searchLink><br /><searchLink fieldCode="DE" term="%22Research+methodology%22">Research methodology</searchLink> – Name: Abstract Label: Abstract Group: Ab Data: The objectives of this study were to investigate the lateral torsional buckling performance of multi-ply structural composite beams to develop experimental procedures to understand their flexural and torsional rigidity that can be used to develop design guidance capable of reliably accounting for their composite capacity. Three 44.5 mm×457 mm×14.8 mm (1.75 in.×18 in.×48.3 ft) laminated veneer lumber beams were nondestructively tested more than 140 times in this investigation using a variety of single and multi-ply member configurations to determine their member stiffness about each primary orientation and joist orientation buckling controlled moment capacity. To allow a wide range of member slenderness to be evaluated, the moment capacity tests used Southwell techniques and single-span bending configurations with two-point loads to determine the critical buckling moment capacity (Mtest′) and torsional rigidity for two different member depths, two different spans, two different relative load point positions, and with up to three beam plies. Multi-ply headers were attached together with nails using a scheme that approximated the manufacturer's minimum recommendations for applications without significant side loads. This study demonstrated that the measured lateral torsional buckling moment capacities were overpredicted where the multi-ply members were assumed to behave with the rigidity of a solid section and underpredicted where the members were assumed to behave as a collection of unattached plies. For the multi-ply beam loading conditions, nail attachment intensities, and bracing methods tested to near their full-scale buckling capacity in this study, Mtest′ was reasonably estimated using predictive calculations that explicitly accounted for torsional rigidity and assumed that the between-ply fastenings provided partial composite action with empirically derived efficiencies of 6% for torsional (GKJ) and 25% for plank orientation flexural (EpIp) rigidity. It was also found that the degree of multi-ply flexural EpIp composite action measured in the plank orientation flexural stiffness tests conducted under different loading and boundary conditions proved to be a poor predictor of relative lateral torsional buckling rigidity in the beam tests and was not correlated to the measured buckling resistance. [ABSTRACT FROM AUTHOR] – Name: AbstractSuppliedCopyright Label: Group: Ab Data: <i>Copyright of Journal of Structural Engineering is the property of American Society of Civil Engineers and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract.</i> (Copyright applies to all Abstracts.) |
| PLink | https://search.ebscohost.com/login.aspx?direct=true&site=eds-live&db=egs&AN=183053948 |
| RecordInfo | BibRecord: BibEntity: Identifiers: – Type: doi Value: 10.1061/JSENDH.STENG-13649 Languages: – Code: eng Text: English PhysicalDescription: Pagination: PageCount: 15 StartPage: 1 Subjects: – SubjectFull: Engineered wood Type: general – SubjectFull: Mechanical buckling Type: general – SubjectFull: Bending strength Type: general – SubjectFull: Flexural strength Type: general – SubjectFull: Design techniques Type: general – SubjectFull: Torsional stiffness Type: general – SubjectFull: Composite construction Type: general – SubjectFull: Research methodology Type: general Titles: – TitleFull: Lateral Torsional Buckling Design for Multi-Ply Structural Composite Lumber Beams. Type: main BibRelationships: HasContributorRelationships: – PersonEntity: Name: NameFull: Waltz, Ned – PersonEntity: Name: NameFull: Amini, M. Omar – PersonEntity: Name: NameFull: Douglas, Bradford IsPartOfRelationships: – BibEntity: Dates: – D: 01 M: 04 Text: Apr2024 Type: published Y: 2025 Identifiers: – Type: issn-print Value: 07339445 Numbering: – Type: volume Value: 151 – Type: issue Value: 4 Titles: – TitleFull: Journal of Structural Engineering Type: main |
| ResultId | 1 |
