View in EDS

High pressure compressive reverse shearing: A new severe plastic deformation process.

Saved in:
Bibliographic Details
Title: High pressure compressive reverse shearing: A new severe plastic deformation process.
Authors: Kumar, Govind1 (AUTHOR), Huilgol, Prashant2 (AUTHOR), Toth, Laszlo S.1,3,4 (AUTHOR) laszlo.toth@univ-lorraine.fr, Suwas, Satyam5 (AUTHOR), Kailas, Satish V2 (AUTHOR)
Source: Materials & Design. Sep2025, Vol. 257, pN.PAG-N.PAG. 1p.
Subjects: Metal fabrication, Shear (Mechanics), Industrial applications, Strain rate, Material plasticity, Mechanical behavior of materials
Abstract: The process is readily up-scalable for industrial-level applications. [Display omitted] • A new single step SPD process for producing UFG metallic sheets is presented. • In HPCRS, compression is combined with oscillating shear to introduce extremely large strain in the metal. • Control strength-ductility combinations by varying the oscillation frequency. • Can process materials with all crystal structures including powders. • High metal forming speed, metallic sheets obtained in less than 15 seconds. Severe plastic deformation (SPD) processing improve mechanical and physical properties but are suffering from inherent limitations, including restricted sample size, low processing speed, and limited strain per cycle, which hinder their industrial adoption. To overcome these challenges, we introduce a novel SPD process termed High Pressure Compressive Reverse Shearing (HPCRS). This technique imposes a large accumulated shear strain in a reciprocating manner, coupled with a uniaxial compressive load, enabling single-step deformation of bulk and powder-consolidated metals. The process has been successfully applied to materials with diverse crystal structures: commercially pure Al, OFHC Cu, IF steel, Zn, and pre-compacted Al and Mg powders. In CP Al, for an 83 % thickness reduction, the estimated equivalent strain, shear strain, and compressive strain were approximately 42, 73, and 1.8, respectively. Ultra-fine grains obtained with a pronounced shear texture. Mechanical testing showed a threefold increase in strength at low processing frequency (0.1 Hz), and good ductility (20–30 %) for all frequencies, accompanied by a decrease in strength (230 MPa to 100 MPa), attributed to strain rate-induced thermal effects. Notably, at 20 Hz, deformation was completed within 15 s. Therefore, HPCRS can be readily applied for industrial-scale metal forming. [ABSTRACT FROM AUTHOR]
Copyright of Materials & Design is the property of Elsevier B.V. and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)
Database: Engineering Source
FullText Text:
  Availability: 0
Header DbId: egs
DbLabel: Engineering Source
An: 187665013
AccessLevel: 6
PubType: Academic Journal
PubTypeId: academicJournal
PreciseRelevancyScore: 0
IllustrationInfo
Items – Name: Title
  Label: Title
  Group: Ti
  Data: High pressure compressive reverse shearing: A new severe plastic deformation process.
– Name: Author
  Label: Authors
  Group: Au
  Data: <searchLink fieldCode="AR" term="%22Kumar%2C+Govind%22">Kumar, Govind</searchLink><relatesTo>1</relatesTo> (AUTHOR)<br /><searchLink fieldCode="AR" term="%22Huilgol%2C+Prashant%22">Huilgol, Prashant</searchLink><relatesTo>2</relatesTo> (AUTHOR)<br /><searchLink fieldCode="AR" term="%22Toth%2C+Laszlo+S%2E%22">Toth, Laszlo S.</searchLink><relatesTo>1,3,4</relatesTo> (AUTHOR)<i> laszlo.toth@univ-lorraine.fr</i><br /><searchLink fieldCode="AR" term="%22Suwas%2C+Satyam%22">Suwas, Satyam</searchLink><relatesTo>5</relatesTo> (AUTHOR)<br /><searchLink fieldCode="AR" term="%22Kailas%2C+Satish+V%22">Kailas, Satish V</searchLink><relatesTo>2</relatesTo> (AUTHOR)
– Name: TitleSource
  Label: Source
  Group: Src
  Data: <searchLink fieldCode="JN" term="%22Materials+%26+Design%22">Materials & Design</searchLink>. Sep2025, Vol. 257, pN.PAG-N.PAG. 1p.
– Name: Subject
  Label: Subjects
  Group: Su
  Data: <searchLink fieldCode="DE" term="%22Metal+fabrication%22">Metal fabrication</searchLink><br /><searchLink fieldCode="DE" term="%22Shear+%28Mechanics%29%22">Shear (Mechanics)</searchLink><br /><searchLink fieldCode="DE" term="%22Industrial+applications%22">Industrial applications</searchLink><br /><searchLink fieldCode="DE" term="%22Strain+rate%22">Strain rate</searchLink><br /><searchLink fieldCode="DE" term="%22Material+plasticity%22">Material plasticity</searchLink><br /><searchLink fieldCode="DE" term="%22Mechanical+behavior+of+materials%22">Mechanical behavior of materials</searchLink>
– Name: Abstract
  Label: Abstract
  Group: Ab
  Data: The process is readily up-scalable for industrial-level applications. [Display omitted] • A new single step SPD process for producing UFG metallic sheets is presented. • In HPCRS, compression is combined with oscillating shear to introduce extremely large strain in the metal. • Control strength-ductility combinations by varying the oscillation frequency. • Can process materials with all crystal structures including powders. • High metal forming speed, metallic sheets obtained in less than 15 seconds. Severe plastic deformation (SPD) processing improve mechanical and physical properties but are suffering from inherent limitations, including restricted sample size, low processing speed, and limited strain per cycle, which hinder their industrial adoption. To overcome these challenges, we introduce a novel SPD process termed High Pressure Compressive Reverse Shearing (HPCRS). This technique imposes a large accumulated shear strain in a reciprocating manner, coupled with a uniaxial compressive load, enabling single-step deformation of bulk and powder-consolidated metals. The process has been successfully applied to materials with diverse crystal structures: commercially pure Al, OFHC Cu, IF steel, Zn, and pre-compacted Al and Mg powders. In CP Al, for an 83 % thickness reduction, the estimated equivalent strain, shear strain, and compressive strain were approximately 42, 73, and 1.8, respectively. Ultra-fine grains obtained with a pronounced shear texture. Mechanical testing showed a threefold increase in strength at low processing frequency (0.1 Hz), and good ductility (20–30 %) for all frequencies, accompanied by a decrease in strength (230 MPa to 100 MPa), attributed to strain rate-induced thermal effects. Notably, at 20 Hz, deformation was completed within 15 s. Therefore, HPCRS can be readily applied for industrial-scale metal forming. [ABSTRACT FROM AUTHOR]
– Name: AbstractSuppliedCopyright
  Label:
  Group: Ab
  Data: <i>Copyright of Materials & Design is the property of Elsevier B.V. and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract.</i> (Copyright applies to all Abstracts.)
PLink https://search.ebscohost.com/login.aspx?direct=true&site=eds-live&db=egs&AN=187665013
RecordInfo BibRecord:
  BibEntity:
    Identifiers:
      – Type: doi
        Value: 10.1016/j.matdes.2025.114450
    Languages:
      – Code: eng
        Text: English
    PhysicalDescription:
      Pagination:
        PageCount: 1
        StartPage: N.PAG
    Subjects:
      – SubjectFull: Metal fabrication
        Type: general
      – SubjectFull: Shear (Mechanics)
        Type: general
      – SubjectFull: Industrial applications
        Type: general
      – SubjectFull: Strain rate
        Type: general
      – SubjectFull: Material plasticity
        Type: general
      – SubjectFull: Mechanical behavior of materials
        Type: general
    Titles:
      – TitleFull: High pressure compressive reverse shearing: A new severe plastic deformation process.
        Type: main
  BibRelationships:
    HasContributorRelationships:
      – PersonEntity:
          Name:
            NameFull: Kumar, Govind
      – PersonEntity:
          Name:
            NameFull: Huilgol, Prashant
      – PersonEntity:
          Name:
            NameFull: Toth, Laszlo S.
      – PersonEntity:
          Name:
            NameFull: Suwas, Satyam
      – PersonEntity:
          Name:
            NameFull: Kailas, Satish V
    IsPartOfRelationships:
      – BibEntity:
          Dates:
            – D: 01
              M: 09
              Text: Sep2025
              Type: published
              Y: 2025
          Identifiers:
            – Type: issn-print
              Value: 02641275
          Numbering:
            – Type: volume
              Value: 257
          Titles:
            – TitleFull: Materials & Design
              Type: main
ResultId 1