Electric conductivity characteristics of FRP and epoxy insulators for GIS under DC voltage.
Saved in:
| Title: | Electric conductivity characteristics of FRP and epoxy insulators for GIS under DC voltage. |
|---|---|
| Authors: | Ueta, Genyo1, Okabe, Shigemitsu1, Utsumi, Tomoaki2, Nukaga, Jun2 |
| Source: | IEEE Transactions on Dielectrics & Electrical Insulation. Aug2015, Vol. 22 Issue 4, p2320-2328. 9p. |
| Subjects: | Electric conductivity, Epoxy insulators, Direct currents, Electric potential, Fiber-reinforced plastics |
| Abstract: | Now that gas insulated switchgear (GIS) for ac systems is becoming increasingly compact as specifications are rationalized, more consideration of their insulation characteristics for residual dc voltage is required. Furthermore, with dc power transmission technology drawing more and more global attention, clarifying the insulation characteristics of GIS for dc voltage is increasingly important. The insulating portions for which the influence of dc voltage must be taken into consideration are solid insulators, such as insulating spacers. Under dc voltage, since the electric field distribution in an insulator differs from that under ac or impulse voltage and is governed by the resistance characteristics, clarifying its characteristics is crucial to study the GIS dc insulation design. As a solid insulator, focusing on fiber-reinforced plastics (FRP) used for GIS, for example, insulating rods, as well as partially treated epoxy resin; this paper experimentally investigated the bulk and surface electric conductivity under dc voltage, using the electric field, temperature, and other factors as parameters. As a result, the bulk electric conductivity of FRP in an edgewise direction exceeded that in the penetrating direction by one digit. It emerged that the electric conductivity of an insulating material with orientation like FRP varied depending on its direction. It was also found that, despite the fact the bulk and surface conductivity depended on the electric field for both FRP and epoxy resin, the variation width was relatively narrow within the range of the actual GIS operating electric field. The bulk and surface electric conductivity were also temperature-dependent, which meant the variation width was relatively wide. Furthermore, the surface electric conductivity was measured in SF6 gas and in the air to investigate the influence of the ambient atmosphere, whereupon it emerged that the electric conductivity was higher in air due to the adherence of moisture. As mentioned above, the electric conductivity of an insulator varies due to various factors, such as the influence of the material orientation, electric field, temperature, and moisture. Consequently, the electric field distribution inside the insulator also changes, meaning these electric conductivity characteristics must be taken into consideration to study the GIS dc insulation characteristics. [ABSTRACT FROM PUBLISHER] |
| Copyright of IEEE Transactions on Dielectrics & Electrical Insulation is the property of IEEE and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.) | |
| Database: | Engineering Source |
| Abstract: | Now that gas insulated switchgear (GIS) for ac systems is becoming increasingly compact as specifications are rationalized, more consideration of their insulation characteristics for residual dc voltage is required. Furthermore, with dc power transmission technology drawing more and more global attention, clarifying the insulation characteristics of GIS for dc voltage is increasingly important. The insulating portions for which the influence of dc voltage must be taken into consideration are solid insulators, such as insulating spacers. Under dc voltage, since the electric field distribution in an insulator differs from that under ac or impulse voltage and is governed by the resistance characteristics, clarifying its characteristics is crucial to study the GIS dc insulation design. As a solid insulator, focusing on fiber-reinforced plastics (FRP) used for GIS, for example, insulating rods, as well as partially treated epoxy resin; this paper experimentally investigated the bulk and surface electric conductivity under dc voltage, using the electric field, temperature, and other factors as parameters. As a result, the bulk electric conductivity of FRP in an edgewise direction exceeded that in the penetrating direction by one digit. It emerged that the electric conductivity of an insulating material with orientation like FRP varied depending on its direction. It was also found that, despite the fact the bulk and surface conductivity depended on the electric field for both FRP and epoxy resin, the variation width was relatively narrow within the range of the actual GIS operating electric field. The bulk and surface electric conductivity were also temperature-dependent, which meant the variation width was relatively wide. Furthermore, the surface electric conductivity was measured in SF6 gas and in the air to investigate the influence of the ambient atmosphere, whereupon it emerged that the electric conductivity was higher in air due to the adherence of moisture. As mentioned above, the electric conductivity of an insulator varies due to various factors, such as the influence of the material orientation, electric field, temperature, and moisture. Consequently, the electric field distribution inside the insulator also changes, meaning these electric conductivity characteristics must be taken into consideration to study the GIS dc insulation characteristics. [ABSTRACT FROM PUBLISHER] |
|---|---|
| ISSN: | 10709878 |
| DOI: | 10.1109/TDEI.2015.005030 |
