Effect of F-EMS position on molten steel flow and solidification in the entire continuous casting strand.
Saved in:
| Title: | Effect of F-EMS position on molten steel flow and solidification in the entire continuous casting strand. |
|---|---|
| Authors: | Yang, Meng1 (AUTHOR) xmli@xauat.edu.cn, Wang, Weian1 (AUTHOR), Yang, Yongkun1 (AUTHOR), Wang, Jianli1 (AUTHOR), Li, Xiaoming1 (AUTHOR) xmli@xauat.edu.cn |
| Source: | Metallurgical Research & Technology. 2026, Vol. 123 Issue 2, p1-12. 12p. |
| Subjects: | Continuous casting, Solidification, Fluid flow, Turbulence, Flow velocity |
| Abstract: | The selection of a rational F-EMS position is of great significance for improving the quality of large round blooms in the combined M-EMS and F-EMS stirring mode. A three-dimensional multi-field coupled mathematical model of the entire curved strand was established to simulate the molten steel flow, heat transfer, and solidification processes under different F-EMS positions. The results indicated that the stirring effect of the F-EMS was primarily concentrated in the middle-upper part of the stirring zone. As the F-EMS position was lowered, the disturbance of the liquid fraction in the stirring zone was gradually reduced, and the maximum flow velocity of the molten steel progressively decreased. When the F-EMS was positioned at 10.5 m from the meniscus, a higher rotational flow velocity was achieved, leading to a significantly enhanced stirring effect. Furthermore, no backflow was observed in the lower zone of the stirrer, and the flow field distribution was uniform. After the application of F-EMS, the solidification end point was shifted upward, and the solidified shell thickness on the inner arc side was consistently greater than that on the outer arc side. At the central crack initiation zone, the application of F-EMS was found to reduce the width of the crack-prone area, thereby decreasing the incidence of quality defects such as central cracks. Therefore, the optimal installation position for the F-EMS is determined to be 10.5 m from the meniscus. This configuration promotes uniform growth of the solidified shell, reduces the width of the crack-prone area at the central crack initiation location, and enhances both the overall bloom quality and the stability of the continuous casting process. [ABSTRACT FROM AUTHOR] |
| Copyright of Metallurgical Research & Technology is the property of EDP Sciences and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.) | |
| Database: | Engineering Source |
|
Full text is not displayed to guests.
Login for full access.
|
|
| Abstract: | The selection of a rational F-EMS position is of great significance for improving the quality of large round blooms in the combined M-EMS and F-EMS stirring mode. A three-dimensional multi-field coupled mathematical model of the entire curved strand was established to simulate the molten steel flow, heat transfer, and solidification processes under different F-EMS positions. The results indicated that the stirring effect of the F-EMS was primarily concentrated in the middle-upper part of the stirring zone. As the F-EMS position was lowered, the disturbance of the liquid fraction in the stirring zone was gradually reduced, and the maximum flow velocity of the molten steel progressively decreased. When the F-EMS was positioned at 10.5 m from the meniscus, a higher rotational flow velocity was achieved, leading to a significantly enhanced stirring effect. Furthermore, no backflow was observed in the lower zone of the stirrer, and the flow field distribution was uniform. After the application of F-EMS, the solidification end point was shifted upward, and the solidified shell thickness on the inner arc side was consistently greater than that on the outer arc side. At the central crack initiation zone, the application of F-EMS was found to reduce the width of the crack-prone area, thereby decreasing the incidence of quality defects such as central cracks. Therefore, the optimal installation position for the F-EMS is determined to be 10.5 m from the meniscus. This configuration promotes uniform growth of the solidified shell, reduces the width of the crack-prone area at the central crack initiation location, and enhances both the overall bloom quality and the stability of the continuous casting process. [ABSTRACT FROM AUTHOR] |
|---|---|
| ISSN: | 22713646 |
| DOI: | 10.1051/metal/2025145 |
